DUSSUN V6i Hyper Class A Amplifier

ML-RR OEM VERSION with Van Den Hul & Kimber IW

OVERVIEW

  The V6i is an extension of Dussun’s high-end product line. The objective of the development of the V6i, built on mature Dussun products, is:

●  to improve sound quality completely;

●  to enhance the power output stage driving; and

●  to improve control capacity upon speakers.

SPECIAL DESIGN FEATURES

  The output stage peak current was designed up to 60 A, and the transformer capacity per channel was designed up to 600 VA. In order to increase sound quality, and to modify the V6i harmonic spectrum for much lower odd order harmonic wave energy, V6i employed the adaptive-bias circuit with an ideal specification.

   Its multi-stage power supply and system loop not only increased the V6i signal-to-noise-ratio to a higher level, but also suppressed the AC power source hum which many times contaminates the purity of the music under a large power output, as well delivered extreme high purity and silence of aural feeling while playing strong dynamic music segments.

   The inner configuration of the V6i followed Dussun’s successful full-symmetrical style. This effective configuration is essential to make the V6i achieve a large power output and low noise objective.

  There is an independent dedicated protection circuit with complete functionality for per channel, which can auto-diagnose probable overload and malfunction, then auto-protect accordingly.

  The preamplifier stage and power amplifier stage are open to the user, allowing the user to use V6i’s either preamplifier stage or power amplifier stage. For general use, V6i’s preamplifier stage and power amplifier stage were linked by a pair of link pins. If the link pins are removed, it is easy for the user to use either V6i’s preamplifier stage or power amplifier stage respectively. The volume control is built in the preamplifier stage, so the preamplifier output signal level is controlled by the volume control knob.

   As a terminal open for the user, the preamplifier stage is driven by a high performance low inner resistance buffer, which can drive many kinds of power amplifiers with more than 600 Ohm input impedance. The volume is not controlled by the volume control knob if the V6i’s power amplifier stage is operated solely.

  The IR (infrared) Remote Control can be used to control the V6i’s volume and input signal selection.

GENERAL:

  RR oem version

  True Dual Mono configuration

  Output power: 165W@8ohms, Class A; 330W@4ohms, Class A

  Infrared remote control

  The preamp and  power amp stages may be used separately

  Dual Mono ultra-low-noise toroidal transformer

  Over 32,000 MFD of filter capacitance per channel

  Minimal internal wiring

  Ultra-short signal path

  Non-magnetic, non-resonant aluminum cover

  Non-invasive protection system

  Microprocessor-controlled passive volume potentiometer

   High quality double-sided printed circuit boards

  Van den Hul + Kimber IW for dynamic and delicate sound

  Exclusive Dussun gold-plated high-current audio connectors

  Detachable power cord system (IEC)

TECHNICAL:  

   PRE-AMP SECTION:

  INPUT IMPEDENCE: 47Kohms

  VOLTAGE GAIN: 14.5db +/- 0.5db

  FREQUENCY RESPONSE: 5Hz – 20Khz +/- 0.5db

  S/N RATIO: >=100db (A weighed)

  MAXIMUM VOLTAGE OUTPUT: >=12Vrms (THD<=0.1%)

  NON-LINEAR DISTORTION: <=0.01% (20Hz – 20KHz, 1.5V)

  PWR-AMP SECTION:

  INPUT IMPEDENCE: 100Kohms

  VOLTAGE GAIN: 29.8db +/- 0.3db (1KHz)

  OUTPUT POWER: 2 x 165W (8ohms); 2 x 330W (4ohms)

  FREQUENCY RESPONSE: 5Hz – 20Khz +/- 1db

  NON-LINEAR DISTORTION: <=0.2% (20Hz – 20KHz, 150W)

  S/N RATIO: >=116db (A weighed)

  DIMENTIONS: 434W x 180H x 420D (mm)

Voltage Standard Available: 220V, 230V

Further Questions: info@cattylink.com

After sales and Warranty: service@cattylink.com